This guide follows National Park Service (NPS) guidance for outdoor bronze plaques and notes where other published advice differs. Bronze is mostly copper with tin, and it reacts with air, rain and pollution, so its surface changes over time. The NPS notes that foundry patinas are most often brown, black or green, with raised letters often lighter than the background, so slow, even darkening is normal. The NPS also explains that corrosion begins once the protective wax wears away, and that it is an ongoing process rather than a stable shield. Signs of damage include green streaks on the bronze and green stains on the stone below, which Preservation Brief 48 links to acid rain dissolving the surface; small powdery green spots, which the NPS says may be “bronze disease” caused by chlorides; a hazy white film of built up wax; and peeling or flaking paint or lacquer. If the corrosion is white or orange, or a magnet sticks to the plaque, the NPS says it is not bronze and this guide does not apply.

What you need

Conserve O Gram 10/5, the NPS leaflet on cleaning and waxing outdoor bronze plaques, lists these basics:

  • Soft brushes with natural or plastic bristles, plus an old toothbrush and a few bamboo skewers for the letters. Wrap any metal band on a brush with tape so it cannot scratch the bronze.
  • Clean water and a hose or pump sprayer. The NPS prefers distilled water, except on polished stone, marble, limestone or concrete, which it can etch.
  • A small amount of non-ionic detergent. The NPS names conservation grade products such as Igepal CA-630, Triton XL-80N and Chemique Ion-417, sold by conservation suppliers.
  • Soft cotton cloths washed without fabric softener, and paper towels.
  • Clear paste wax, if you plan to wax. The NPS names Butcher’s White Diamond Bowling Alley Wax, Trewax Paste Wax (clear) and Johnson’s Paste Wax (clear), thinned with mineral spirits or a similar petroleum solvent.
  • For waxing: nitrile gloves, a respirator with organic vapour cartridges, aluminium foil and a horsehair shoe brush.

Do not use

  • Wire or metal bristle brushes: they scratch (Preservation Brief 48).
  • Abrasive pads or scouring powder: they remove patina and metal (NPS Tech Note).
  • Power washers: high pressure water damages markers (Preservation Brief 48).
  • Vinegar or lemon juice: acids, which can attack metals (Preservation Brief 48).
  • Salt, including road salt: chlorides are linked to bronze disease (NPS).
  • Bleach: leaves salt residues (Preservation Brief 48; NPS cemetery tips).
  • Ammonia: can dissolve copper (Canadian Conservation Institute).
  • Brass or metal polish: many contain ammonia or hard abrasives and leave residues (Canadian Conservation Institute), and polishing strips the patina.

Cleaning steps

These steps follow Conserve O Gram 10/5. Inspect and photograph the plaque first, and clean on a bright, dry, warm day. Preservation Brief 48 recommends washing only when the air is above 40 °F (about 4 °C) for the work and the following 24 hours.

  1. Brush away loose dirt with a dry, soft brush, using a skewer in the letters.
  2. Soak the surface below the plaque with clean water and keep it wet, so dirty rinse water cannot soak in.
  3. Scrub the plaque gently with water and a small amount of non-ionic detergent, using natural or plastic bristle brushes. This removes packed dirt and loose corrosion.
  4. Rinse thoroughly with clean water, pouring it over the plaque or spraying it from a hose or pump sprayer, until no soap remains.
  5. Repeat the wash if the plaque is very dirty.
  6. Let the plaque dry completely. Blot standing water with a clean sponge or cloth rather than wiping. A hair dryer can speed drying.

The NPS notes the plaque may then look darker and less green, but not new. That is expected.

Waxing and protective coatings

The NPS recommends a thin coat of wax as a barrier against moisture that also makes graffiti easier to remove. Conserve O Gram 10/5 describes “cold” waxing; “hot” waxing with a torch is for conservators only.

  1. Tuck strips of doubled aluminium foil between the plaque and the stone to keep wax off the stone, and wet the stone again.
  2. Mix about half a cup of paste wax with roughly the same amount of mineral spirits until smooth, about the thickness of heavy cream. Wear gloves and the respirator.
  3. On a completely dry plaque, brush on a thin layer, working it into every letter and edge. The NPS rule is “the less the better”.
  4. Wait until the plaque looks dry and the solvent smell has faded.
  5. Remove all excess wax, especially from the letters, because built up wax turns white and flakes.
  6. Buff firmly with a clean cotton cloth, using a toothbrush in the letters.
  7. Apply a second thin coat, buff again, then give a final buff with a horsehair shoe brush.

Solvents and used rags are flammable and hazardous; follow local disposal rules. Note the date and products used.

How often

ConditionsNPS suggested schedule
Most locationsInspect and wax once a year
Coastal, very rainy or humidTwice a year may be needed
Dry climatesEvery two to three years
Windy sites with blowing gritMore often than once a year

The NPS bronze sculpture Tech Note agrees: wax lasts one to three years outdoors, so inspect yearly, wash lightly and rewax where it has worn.

Lacquered and factory finished plaques

The NPS notes that modern plaques are often coated with clear or pigmented lacquer or baked enamel. Here published practice differs. NPS conservation guidance uses wax, which is easy to renew, and the Canadian Conservation Institute notes that lacquer always changes the look of the metal and is hard to remove. Plaque makers and the NPS National Natural Landmarks program use lacquer: new landmark plaques come with a black oxide finish and an automotive grade clear coat, and the program says a mild solution of dish soap and water is usually all they need. An NCPTT team treating national cemetery plaques matched wax or lacquer to what each plaque already had. If your plaque has an intact factory coating, wash it gently and leave the coating alone. If that coating is peeling or flaking, the NPS advice is to call a conservator rather than to wax over it.

Seasonal checklist

For Canadian and northern US conditions. Preservation Brief 48 notes that salt and freeze and thaw cycles together do more damage than either alone.

Spring

  • Once days stay above 4 °C, rinse off winter grit and any salt spray with clean water.
  • Do your yearly inspection: photograph the plaque, check every bolt head and edge, and note any new streaks, spots or flaking.

Summer

  • Clean and wax on a warm, dry day, which the NPS calls ideal.
  • Ask the cemetery or grounds crew to take care with mowers and string trimmers near flat markers. Preservation Brief 48 notes these are easily damaged by machinery, fertilisers and weed killers.
  • Check that sprinklers do not soak the plaque. The NPS landmarks guide says a steady stream of water ages a plaque faster.

Autumn

  • Clear leaves, grass clippings and soil off the plaque so it does not stay damp.
  • Look at the most exposed areas. The NPS Tech Note says bronze turns matte where the wax has worn away; renew the wax there before the cold weather.

Winter

  • Do not wash or wax below 4 °C.
  • Keep de-icing salt off and away from the plaque, since salt is a chloride.
  • Brush snow off gently with a soft brush. Do not chip ice or use a metal shovel on the face; scratches are surface damage.

When to call a conservator

Conserve O Gram 10/5 covers only routine cleaning and waxing. The NPS says to call a conservator when you see:

  • Missing bolt heads.
  • Peeling or flaking paint, lacquer or other coatings.
  • Graffiti.
  • Any other problem it does not cover, such as a loose plaque, or green corrosion that remains after a careful wash, especially powdery spots, which the NPS says may be fast moving bronze disease.

Preservation Brief 48 adds that loose or detached markers should be corrected promptly, and suggests the American Institute for Conservation’s “Find a Conservator” directory. Ask for a written plan and a completion report.

Printable checklist

Bronze memorial plaque care, based on National Park Service guidance. Keep with the plaque’s records.

Every year

  • □Photograph the plaque and note its condition and the date
  • □Check bolt heads, edges and mounting
  • □Brush off loose dirt with a soft, dry brush
  • □Wet the stone below and keep it wet
  • □Wash with water and a little non-ionic detergent
  • □Rinse well and let dry completely
  • □Apply a thin coat of clear paste wax, remove excess, buff
  • □Second thin coat, buff, final buff with a horsehair brush

By season

  • □Spring: rinse off winter grit and salt once above 4 °C
  • □Summer: clean and wax on a warm, dry day; check mowers and sprinklers
  • □Autumn: clear leaves and clippings; renew dull wax
  • □Winter: no washing; no salt near the plaque; soft brush for snow

Never use

  • □Wire brushes, abrasive pads, power washers
  • □Vinegar, lemon, salt, bleach, ammonia, metal polish

Call a conservator for

  • □Missing bolt heads or a loose plaque
  • □Peeling or flaking coating
  • □Graffiti
  • □Green corrosion or powdery spots that do not wash off

Sources

This guide was prepared by Bronze Plaque, a company in Oshawa, Ontario that casts bronze plaques and ships them across Canada and the US. For a shorter walkthrough, see our page on how to clean a bronze memorial plaque. If you are planning a new memorial, you can lay out the wording in our online plaque designer.